Electrical fundamentals practice
64 free, original questions with worked explanations. Choose a topic or work through the full set at your own pace.
Progress can’t be saved in this browser. Keep this page open to finish your set.
Build a practice set
Practice results
Review your answers
Practice worksheet
Choose your answer, then open the explanation to check your reasoning.
Circuit math
-
A 36 V DC source is across a 9 Ω resistor in a circuit diagram. What current flows through the resistor?
- 1.5 A
- 4 A
- 27 A
- 45 A
Show answer
B. 4 A
Use I = V ÷ R. Divide 36 V by 9 Ω to get 4 A. The voltage is the drop across this resistor, so no other circuit values are needed.
-
A 48 V DC source feeds 4 Ω, 8 Ω, and 12 Ω resistors in series. What is the voltage drop across the 8 Ω resistor?
- 8 V
- 12 V
- 24 V
- 16 V
Show answer
D. 16 V
The series resistance is 4 Ω + 8 Ω + 12 Ω = 24 Ω. That gives a current of 48 V ÷ 24 Ω = 2 A through all three resistors. Across the 8 Ω resistor, the drop is 2 A × 8 Ω = 16 V.
-
A 24 V DC source feeds two parallel branches. One branch is 12 Ω and the other is 6 Ω. How much current does the source deliver?
- 6 A
- 2 A
- 4 A
- 12 A
Show answer
A. 6 A
Each branch sees 24 V. The 12 Ω branch draws 24 V ÷ 12 Ω = 2 A, and the 6 Ω branch draws 24 V ÷ 6 Ω = 4 A. The source supplies both branches, for a total of 6 A.
-
A simplified 10 V DC circuit models its leads as a combined 2 Ω in series with an 8 Ω load. What voltage appears across the load?
- 2 V
- 5 V
- 8 V
- 10 V
Show answer
C. 8 V
The total resistance is 2 Ω + 8 Ω = 10 Ω, so the current is 10 V ÷ 10 Ω = 1 A. The load voltage is 1 A × 8 Ω = 8 V. The remaining 2 V drops across the modeled lead resistance.
-
A 24 V DC source feeds a 4 Ω resistor in series with a parallel pair of 6 Ω and 3 Ω. How much current flows in the 3 Ω branch?
- 1.33 A
- 2.67 A
- 4.00 A
- 8.00 A
Show answer
B. 2.67 A
The parallel pair is 2 Ω, so the total is 6 Ω and the source delivers 4 A. The pair has 4 A × 2 Ω = 8 V across it. The 3 Ω branch draws 8 V ÷ 3 Ω ≈ 2.67 A.
-
One branch across a 30 V DC source contains a 10 Ω resistor. A second parallel branch contains 5 Ω and 15 Ω in series. What is the total current?
- 1.0 A
- 3.0 A
- 4.5 A
- 11.0 A
Show answer
C. 4.5 A
First reduce the second branch to 20 Ω. Each branch sees 30 V, so the currents are 30 ÷ 10 = 3 A and 30 ÷ 20 = 1.5 A. Add them to get 4.5 A.
-
A 24 V DC source drives a 4 Ω resistor and an unknown resistor in series. The 4 Ω resistor drops 8 V. What is the unknown resistance?
- 8 Ω
- 4 Ω
- 12 Ω
- 16 Ω
Show answer
A. 8 Ω
The measured drop gives 8 V ÷ 4 Ω = 2 A through both resistors. The unknown resistor accounts for 24 V − 8 V = 16 V. Its resistance is 16 V ÷ 2 A = 8 Ω.
-
Two resistors are in parallel across an 18 V DC source that delivers 6 A in total. The first branch has a 6 Ω resistor. What is the resistance of the second branch?
- 3 Ω
- 9 Ω
- 12 Ω
- 6 Ω
Show answer
D. 6 Ω
The first branch draws 18 V ÷ 6 Ω = 3 A. Subtract 3 A from 6 A to find 3 A in the second branch. It also sees 18 V, so its resistance is 6 Ω.
-
Two resistors are in parallel directly across an ideal 12 V DC source. One branch opens. What happens to the current through the intact resistor and the total current?
- The intact current rises, and the total stays the same
- The intact current stays the same, and the total drops
- Both currents drop
- Both currents stay the same
Show answer
B. The intact current stays the same, and the total drops
The source still holds 12 V across the intact resistor, so that branch draws the same current. The source no longer supplies the opened branch, so the total current drops.
-
An ideal DC voltage source feeds a fixed resistor in series with two equal parallel loads. One load opens. What happens to the total current and the voltage across the remaining load?
- The total current drops, and the remaining load voltage rises
- The total current drops, and the remaining load voltage drops
- The total current stays the same, and the remaining load voltage rises
- The total current rises, and the remaining load voltage stays the same
Show answer
A. The total current drops, and the remaining load voltage rises
With one branch gone, the equivalent load resistance rises. Total resistance rises and total current falls. The series resistor then drops less voltage, leaving more across the remaining load.
-
A student claims two resistive branches measured at the same instant draw 2 A and 3 A from a DC source that delivers 4 A. Both branch currents flow away from the supply junction. What should the student conclude?
- The 4 A agrees because it falls between 3 A and 5 A
- The 4 A agrees if the branches have equal voltage
- The readings disagree because the source should supply 5 A
- The readings disagree because the source should supply 1 A
Show answer
C. The readings disagree because the source should supply 5 A
Current entering the junction must equal current leaving it. The two branch currents flow away from the junction, so they add to 5 A. At least one reading or assumption about the circuit needs checking.
-
Two 6 Ω resistors are in series across an 18 V DC source. A 6 Ω load is placed in parallel with the lower resistor. What voltage is across the load?
- 9 V
- 12 V
- 18 V
- 6 V
Show answer
D. 6 V
The lower resistor and load combine to 3 Ω. That pair and the upper 6 Ω resistor make 9 Ω total, so the source supplies 2 A. The pair drops 2 A × 3 Ω = 6 V, which is also the load voltage.
-
A DC circuit diagram shows an ideal 18 V source and 3 Ω and 6 Ω in series. An ideal closed switch bypasses only the 3 Ω resistor. What current flows through the 6 Ω resistor after the switch closes?
- 2 A
- 3 A
- 6 A
- 0 A
Show answer
B. 3 A
The closed switch gives the 3 Ω resistor a zero-resistance bypass, leaving 0 V across that resistor. The 6 Ω resistor still has a path to the source and sees all 18 V, which gives 3 A.
-
A simplified 12 V DC model has a 5 Ω load and a lead on each side of the load. Each lead contributes 0.5 Ω. What voltage appears across the load?
- 10 V
- 11 V
- 10.91 V
- 2 V
Show answer
A. 10 V
Both lead resistances are in series with the load, so the total is 0.5 + 5 + 0.5 = 6 Ω. The current is 12 ÷ 6 = 2 A. The load drop is 2 × 5 = 10 V.
-
A 120 V RMS AC source feeds 20 Ω and 40 Ω ideal resistors in series. What is the RMS voltage across the 40 Ω resistor?
- 40 V
- 56.6 V
- 113.1 V
- 80 V
Show answer
D. 80 V
For this purely resistive circuit, use Ohm’s law with RMS values. The current is 120 ÷ (20 + 40) = 2 A RMS, so the 40 Ω resistor drops 80 V RMS.
-
A student gets 9 Ω for the equivalent resistance of a 6 Ω resistor in parallel with a 12 Ω resistor. What is the quickest check?
- 9 Ω is reasonable because it is their average
- Any parallel result must exceed 12 Ω
- The equivalent resistance must be lower than 6 Ω
- The pair must equal 6 Ω because current takes the easier path
Show answer
C. The equivalent resistance must be lower than 6 Ω
Both branches carry current at the same voltage. Together they draw more current than the 6 Ω branch alone, so the equivalent resistance is lower than 6 Ω. Taking the reciprocal of 1/6 + 1/12 gives 4 Ω.
Power & energy
-
A purely resistive load draws 7.5 A from a 120 V RMS source. How much real power does it consume?
- 16 W
- 112.5 W
- 900 W
- 960 W
Show answer
C. 900 W
A purely resistive AC load has a power factor of 1. Multiply the RMS quantities, 120 V × 7.5 A, to get 900 W of real power.
-
A training example shows a 1,200 W load running continuously for 2.5 hours. How much energy does it use?
- 3.0 kWh
- 0.48 kWh
- 1.2 kWh
- 3,000 kWh
Show answer
A. 3.0 kWh
Divide 1,200 W by 1,000 to get 1.2 kW. Multiply that power by the 2.5 h run time to get 3.0 kWh.
-
A model circuit shows 4 A of DC current through a 0.5 Ω resistance. How much power is dissipated in that resistance?
- 2 W
- 4 W
- 32 W
- 8 W
Show answer
D. 8 W
Use P = I² × R because current and resistance are given. Squaring 4 A gives 16 A². Multiply by 0.5 Ω to get 8 W.
-
A motor delivers 800 W of mechanical power at 80% efficiency. What electrical input power does it draw at that operating point?
- 640 W
- 1,000 W
- 960 W
- 800 W
Show answer
B. 1,000 W
Efficiency is output power divided by input power. Rearrange to find input power and divide 800 W by 0.80. The result is 1,000 W, with 200 W of losses.
-
A 24 V DC source feeds 2 Ω and 6 Ω in series. What power is dissipated by the 6 Ω resistor?
- 18 W
- 48 W
- 54 W
- 72 W
Show answer
C. 54 W
The series current is 24 V ÷ 8 Ω = 3 A. The 6 Ω resistor dissipates (3 A)² × 6 Ω = 54 W. The 72 W figure is the power of both resistors together.
-
A 4 Ω resistor and an 8 Ω resistor are in parallel across a fixed DC voltage. How does the power in the 4 Ω resistor compare with the power in the 8 Ω resistor?
- It is twice as high
- It is half as high
- It is four times as high
- It is the same
Show answer
A. It is twice as high
Both resistors see the same voltage. In P = V² ÷ R, halving resistance at a fixed voltage doubles power.
-
In a circuit model, a cable has the same resistance at two operating points. Current rises from 3 A to 6 A. By what factor does the resistive loss increase?
- 2
- 3
- 6
- 4
Show answer
D. 4
The resistance stays fixed. The ratio of losses is (6 A ÷ 3 A)² = 4, because resistive loss is I² × R.
-
A device uses 900 W for 20 minutes and 300 W for the next 40 minutes. What total energy does it use?
- 0.30 kWh
- 0.50 kWh
- 0.60 kWh
- 1.20 kWh
Show answer
B. 0.50 kWh
The first mode uses 0.9 kW × 1/3 h = 0.30 kWh. The second uses 0.3 kW × 2/3 h = 0.20 kWh. Add the two intervals to get 0.50 kWh.
-
A modeled heater draws 2 kW when on and zero when off. In a 5-hour period it is on for 30% of the time. How much energy does it use?
- 1.5 kWh
- 3 kWh
- 7 kWh
- 10 kWh
Show answer
B. 3 kWh
The heater is on for 0.30 × 5 h = 1.5 h. Multiply by 2 kW to get 3 kWh.
-
Two setups do the same task each day. A uses 1.2 kW for 30 minutes, and B uses 0.8 kW for 60 minutes. At $0.20 per kWh, how much less does A cost to run over 10 days?
- $0.04
- $0.16
- $0.40
- $2.00
Show answer
C. $0.40
A uses 0.60 kWh each day and B uses 0.80 kWh. Over 10 days the difference is 2.0 kWh. At $0.20 per kWh, A costs $0.40 less.
-
An energy meter reading rises from 184.2 kWh to 185.1 kWh over 15 minutes. What was the average power during that interval?
- 3.6 kW
- 0.9 kW
- 0.225 kW
- 13.5 kW
Show answer
A. 3.6 kW
The change is 0.9 kWh over 0.25 h. Divide energy by time to find the average power, 0.9 ÷ 0.25 = 3.6 kW.
-
A motor takes 1.5 kW of real input power at 80% efficiency and runs for 2 hours. How much input energy is lost inside the motor rather than delivered as mechanical work?
- 0.30 kWh
- 1.20 kWh
- 2.40 kWh
- 0.60 kWh
Show answer
D. 0.60 kWh
The loss is 20% of 1.5 kW, or 0.30 kW. At that loss rate for 2 hours, the energy lost is 0.60 kWh.
-
In a model, an ideal 60 Ω heating resistor is tested at both 120 V RMS and 60 V RMS. How much real power does it consume at 60 V RMS?
- 120 W
- 240 W
- 60 W
- 30 W
Show answer
C. 60 W
For a purely resistive load use P = V² ÷ R with RMS voltage. At 60 V, the power is 60² ÷ 60 = 60 W. This is one quarter of the 240 W at 120 V.
-
A 30 V DC source feeds a 5 Ω series resistor and a 10 Ω load. What fraction of the source power reaches the load?
- One third
- Two thirds
- One half
- All of it
Show answer
B. Two thirds
The same current flows through both resistors. Since P = I² × R, the fraction going to the load is 10 Ω ÷ (5 Ω + 10 Ω) = 2/3.
-
A practice setup has 480 Wh of available energy. Two devices draw a combined constant 160 W. Ignoring losses, how long can they run?
- 3 hours
- 0.33 hours
- 7.68 hours
- 300 hours
Show answer
A. 3 hours
Time is energy divided by power. Watt-hours divided by watts gives hours, so 480 Wh ÷ 160 W = 3 h.
-
A 2 Ω resistor and an 8 Ω resistor both dissipate 32 W in separate DC circuits. Which pair of voltages is across the 2 Ω and 8 Ω resistors, respectively?
- 4 V and 2 V
- 16 V and 8 V
- 16 V and 4 V
- 8 V and 16 V
Show answer
D. 8 V and 16 V
Solve P = V² ÷ R for voltage. The 2 Ω resistor needs √(32 × 2) = 8 V, and the 8 Ω resistor needs √(32 × 8) = 16 V.
AC & transformers
-
An ideal transformer has 600 primary turns and 300 secondary turns. Its primary voltage is 120 V RMS. What is its secondary voltage?
- 30 V RMS
- 60 V RMS
- 120 V RMS
- 240 V RMS
Show answer
B. 60 V RMS
The secondary has 300 ÷ 600 = 0.5 times as many turns as the primary. Apply the same ratio to the voltage. The secondary voltage is 120 V × 0.5 = 60 V RMS.
-
An ideal transformer has 240 V RMS across its primary and 48 V RMS across its secondary. With 5 A RMS flowing on the secondary, what is the primary current?
- 0.2 A RMS
- 5 A RMS
- 25 A RMS
- 1 A RMS
Show answer
D. 1 A RMS
The secondary apparent power is 48 V × 5 A = 240 VA. With an ideal transformer, the apparent power at the primary is also 240 VA. Divide by the primary voltage of 240 V to get 1 A RMS.
-
A single-phase load has 240 V RMS, 4 A RMS, and a power factor of 0.75. What is its real power?
- 720 W
- 960 W
- 320 W
- 1,280 W
Show answer
A. 720 W
Voltage times current gives 240 V × 4 A = 960 VA of apparent power. Multiply by the 0.75 power factor to get 720 W of real power.
-
A balanced three-phase load draws 10 A RMS of line current at 208 V RMS line-to-line. What is its apparent power to the nearest tenth of a kilovolt-ampere?
- 1.2 kVA
- 2.1 kVA
- 3.6 kVA
- 6.2 kVA
Show answer
C. 3.6 kVA
For a balanced three-phase load, S = √3 × line-to-line voltage × line current. Multiply √3 × 208 V × 10 A to get approximately 3,603 VA. Divide by 1,000 and round to get 3.6 kVA.
-
A sinusoidal source has a peak voltage of 170 V. What is its RMS voltage, rounded to the nearest volt?
- 85 V
- 120 V
- 170 V
- 240 V
Show answer
B. 120 V
For a sine wave, RMS voltage is peak voltage divided by √2. So 170 V ÷ √2 rounds to 120 V.
-
A sinusoidal source with zero DC offset and a 48 V peak-to-peak voltage is across a 12 Ω resistor. What is the average power?
- 24 W
- 48 W
- 96 W
- 192 W
Show answer
A. 24 W
The peak voltage is 24 V, half the peak-to-peak value. Voltage squared in RMS terms is 24² ÷ 2 = 288 V². Divide by 12 Ω to get 24 W.
-
An ideal transformer has 500 primary turns and 100 secondary turns. A 4 Ω resistor is across the secondary. With 120 V RMS at the primary, what RMS current does the primary draw?
- 0.24 A
- 6.0 A
- 1.2 A
- 30 A
Show answer
C. 1.2 A
The secondary voltage is 120 × (100 ÷ 500) = 24 V RMS. The resistor draws 24 ÷ 4 = 6 A RMS, so the secondary supplies 144 VA. The primary draws 144 ÷ 120 = 1.2 A RMS.
-
A single-phase transformer is rated 480 VA at 24 V on the secondary. A load is already drawing 13 A RMS. How much more resistive load current can it supply within its rating if the existing load is also purely resistive?
- 13 A
- 20 A
- 33 A
- 7 A
Show answer
D. 7 A
The full rated current is 480 VA ÷ 24 V = 20 A. With both loads resistive, their currents are in phase and add directly. Subtract 13 A to get 7 A of remaining capacity in this model.
-
An ideal transformer steps 48 V RMS up to 192 V RMS. The secondary delivers 2 A RMS. What RMS current is drawn at the primary?
- 8 A RMS
- 0.5 A RMS
- 2 A RMS
- 4 A RMS
Show answer
A. 8 A RMS
The secondary supplies 192 V × 2 A = 384 VA. The primary draws that same apparent power at 48 V, so its current is 384 ÷ 48 = 8 A RMS.
-
A winding with 1,000 turns is supplied with 240 V RMS. In an ideal transformer, how many secondary turns give 36 V RMS?
- 36 turns
- 240 turns
- 150 turns
- 6,667 turns
Show answer
C. 150 turns
The secondary needs 36 ÷ 240 = 0.15 times the primary turns. Multiply 1,000 by 0.15 to get 150 turns.
-
A single-phase AC load takes 1,440 W of real power at 120 V RMS and a power factor of 0.80. What RMS current does it draw?
- 9.6 A
- 12 A
- 18 A
- 15 A
Show answer
D. 15 A
Use P = V × I × power factor. Solving for current gives 1,440 W ÷ (120 V × 0.80) = 15 A RMS.
-
A single-phase load takes 750 W at 125 V RMS. Its line current is 8 A RMS. What is its power factor?
- 0.60
- 0.75
- 0.94
- 1.33
Show answer
B. 0.75
Apparent power is 125 V × 8 A = 1,000 VA. Divide 750 W by 1,000 VA to get a power factor of 0.75.
-
A single-phase system delivers the same real power at the same RMS voltage before and after its power factor rises from 0.60 to 0.90. What fraction of the original line current is now drawn?
- 1/3
- 2/3
- 9/10
- 3/2
Show answer
B. 2/3
At fixed watts and voltage, current scales inversely with power factor. The new current divided by the old current is 0.60 ÷ 0.90 = 2/3.
-
An ideal transformer has 240 V RMS at the primary and 60 V RMS at the secondary. Its single-phase load draws 12 A RMS at a power factor of 0.75. What real power does the transformer draw at the primary?
- 720 W
- 2,160 W
- 540 W
- 180 W
Show answer
C. 540 W
At the secondary, apparent power is 60 × 12 = 720 VA and real power is 720 × 0.75 = 540 W. The ideal transformer has zero losses, so real input power is also 540 W.
-
A balanced wye-connected system has 208 V RMS line-to-line. What voltage is measured from a line to neutral, to the nearest volt?
- 69 V RMS
- 104 V RMS
- 208 V RMS
- 120 V RMS
Show answer
D. 120 V RMS
For a balanced wye system, line-to-line voltage is √3 times line-to-neutral voltage. Divide 208 V by √3 to get about 120 V RMS.
-
A balanced three-phase load draws 10 A RMS of line current at 480 V RMS line-to-line with a power factor of 0.85. What real power does it draw to the nearest tenth of a kilowatt?
- 7.1 kW
- 4.1 kW
- 8.3 kW
- 12.2 kW
Show answer
A. 7.1 kW
Calculate apparent power first. √3 × 480 × 10 ≈ 8,314 VA. Multiply by 0.85, divide by 1,000, and round to get 7.1 kW.
Codebook skills
-
A practice question names equipment that seems to match two sections in the index. What should you read first to decide which section covers the scenario?
- The section with the larger tables
- The section that has the shorter title
- The scope of each section
- The section that appears first in the book
Show answer
C. The scope of each section
The index points you to possible sections. The scope tells you which equipment or situations the section covers. Compare both scopes with the facts in the question before applying any rule.
-
In a fictional worksheet table, the first row covers lengths up to and including 12 m. The second row covers lengths greater than 12 m. A note says to use total length, including an extension. The main length is 11 m and the extension is 1.5 m. Which row applies?
- The second row, using 12.5 m
- The first row, using 11 m
- The first row, using 1.5 m
- The first row, using 12 m
Show answer
A. The second row, using 12.5 m
The note defines the input to the table. Add 11 m and 1.5 m to get 12.5 m. That value is greater than 12 m and falls in the second row.
-
A fictional exam excerpt gives an exception for items that are indoors and accessible without a tool. An item is indoors, but reaching it requires a tool. Which reading is supported?
- The exception applies because the item is indoors
- The exception applies if the tool is nearby
- The exception applies if either condition is met
- The general rule applies because both conditions must be met
Show answer
D. The general rule applies because both conditions must be met
The word “and” joins two required conditions. The item meets the location condition and fails the access condition. That leaves the general rule in effect under this excerpt.
-
An exam problem turns on a technical term that has a familiar everyday meaning. What source should you check for how the term is used in the problem’s cited code section?
- A general dictionary entry
- The applicable definitions in the cited code edition
- The index entry by itself
- The latest edition’s glossary, regardless of the cited edition
Show answer
B. The applicable definitions in the cited code edition
A definition can set the boundaries for a term in an entire codebook or a particular section. Check which definition applies and use the edition named in the problem.
-
A fictional section lists the usual rule, then says portable assemblies must follow Section B instead. The question describes a portable assembly. What should you do next?
- Use the usual rule because it appears first
- Read Section B and check its conditions against the assembly
- Skip Section B unless it appears in the index
- Choose whichever section gives the simpler result
Show answer
B. Read Section B and check its conditions against the assembly
The first section directs you to Section B for this category. Read the referenced section, then compare its scope and conditions with the facts given.
-
A study guide points to a familiar section number. In the edition specified by the question, that number has an unrelated heading. What is the best way to recover?
- Use the older wording from the study guide
- Read the unrelated section and apply the closest sentence
- Find the subject through the specified edition’s index or contents, then verify the scope
- Always adopt the wording from the newest edition
Show answer
C. Find the subject through the specified edition’s index or contents, then verify the scope
Chapter and section numbers can change across editions. Search by subject in the named edition and confirm that the section you find covers the scenario.
-
A fictional excerpt permits a method when either Condition A or Condition B is met, provided approval is documented. Condition A is met, Condition B is unmet, and approval is undocumented. What follows?
- The permission is unavailable because documented approval is also required
- The method is permitted because Condition A is met
- Both conditions are required before documentation matters
- The method is permitted if either the condition or documentation is present
Show answer
A. The permission is unavailable because documented approval is also required
Condition A satisfies the choice between A and B. The phrase “provided approval is documented” adds a separate requirement, which the scenario fails to satisfy.
-
A fictional table has rows “less than 5 units,” “5 through 10 units,” and “greater than 10 units.” Its note says to use the combined value of all parts. Two parts are each 5 units. Which row applies?
- Less than 5 units
- Greater than 10 units
- No row covers exactly 10 units
- 5 through 10 units
Show answer
D. 5 through 10 units
The note makes the table input 5 + 5 = 10 units. The wording “5 through 10 units” includes both endpoints. The last row starts above 10.
-
A fictional table has indoor and outdoor columns for each equipment type. Its note says covered outdoor spaces still use the outdoor column. A Type B unit sits outdoors beneath a canopy. Which entry applies?
- Type A, outdoor
- Type B, outdoor
- Type B, indoor
- Either Type B entry
Show answer
B. Type B, outdoor
Choose the Type B row from the equipment description. Apply the table note to the canopy location and select the outdoor column.
-
A fictional rule requires a value of at least 4 units and at most 7 units. An explanatory note gives an example of 6 units. Which listed set contains every whole-number value the rule allows?
- 4, 5, 6, and 7 units
- 5 and 6 units
- 6 units only
- 4, 5, and 6 units
Show answer
A. 4, 5, 6, and 7 units
“At least” and “at most” include the stated endpoints. All whole numbers from 4 to 7 qualify. The example of 6 illustrates one value in that range.
-
A fictional worksheet table uses a row for total length and a column for equipment type. The question supplies the length but omits equipment type. The two types give different results. What should you conclude?
- Use the first column
- Average the column values
- Assume the more common equipment type
- The table entry cannot be determined from the facts given
Show answer
D. The table entry cannot be determined from the facts given
Length determines the row. Equipment type is needed to select a unique column, and the two entries differ. Explain which fact is missing.
-
A fictional table uses centimeters and gives three bands: less than 90 cm, 90–110 cm inclusive, and more than 110 cm. The problem gives a length of 1.05 m. Which band applies?
- Less than 90 cm
- More than 110 cm
- 90–110 cm inclusive
- There is no matching band because the input is in meters
Show answer
C. 90–110 cm inclusive
Convert to the table’s units before choosing the row. Multiply 1.05 m by 100 cm per meter to get 105 cm, which lies in the middle band.
-
A candidate section is titled “Equipment enclosures.” Its scope says it covers permanent enclosures and excludes temporary transport cases. The item in the question is a temporary transport case. What is the next useful step?
- Apply the section because its title includes “enclosures”
- Consult the contents or index for a provision that covers temporary transport cases
- Apply only the table in the excluded section
- Treat the exclusion as permission to use the case without conditions
Show answer
B. Consult the contents or index for a provision that covers temporary transport cases
The stated exclusion rules out this section for the item described. Use the item’s category to look for another applicable provision.
-
A fictional excerpt defines a “mobile unit” as equipment intended to move during normal operation. A permanently installed unit was moved by a cart before installation. Which fact controls the classification?
- The unit stays in place during normal operation
- A cart moved it once
- The enclosure looks like other mobile equipment
- The unit could be removed for replacement
Show answer
A. The unit stays in place during normal operation
The provided definition turns on intended movement during normal operation. Moving the unit before it is installed does not satisfy that condition.
-
A fictional rule says both a cover and a label are required. Its exception waives the label for demo units. The item is a demo unit. What is required under this excerpt?
- Both a cover and a label
- Neither a cover nor a label
- Only a label
- Only a cover
Show answer
D. Only a cover
The exception specifically waives the label. The cover remains required by the general rule.
-
In a fictional table, an asterisk marks two cells. The note says starred values apply only when a form is on file. Your row and column meet at an unstarred cell, and no form is on file. What should you conclude about this note?
- The form condition bars every value in the table
- Use the nearest starred cell instead
- The form condition does not apply to the unstarred cell
- The missing form means the row and column can be chosen again
Show answer
C. The form condition does not apply to the unstarred cell
The note identifies starred cells as the ones with the additional condition. Check any other applicable instructions, then use the value at the matching row and column.
For your exam format, allowed references, and licensing requirements, start with your state’s guide.
Find your state